Chimney Top — Caps, Covers & Draft · Anchor Component

Copper Chase Cover (Custom-Fabricated)

Solid-copper chase top, fully sloped and standing-seamed, cut to fit your exact chase so it sheds water instead of pooling it. Copper never rusts and never needs replacing, so it ages to a patina rather than streaking a stain down your siding, and over the life of the house it costs less than the galvanized cover you would end up redoing twice. We template the chase in person before we fabricate, because a cover that is only close is a cover that leaks. While the crew is up top setting it, they can knock out the sweep, cap, and dryer-vent check in the same visit.

Specification

What the listing decides

Material: Solid copper
Store fit: Quote-to-fabricate, measured on site

How this part is bought

The part follows the finding

No part in this store is a loose transaction. This one links back to the graded inspection that surfaces the need, and across to the install service it belongs to — both performed by the same trained crew.

Upstream

Chimney Inspection

The graded inspection that documents the need for this part before it ships.

Start here

Installed by

Chase Cover Replacement

The install service this component attaches to, fitted to its listing by the same crew.

See the work

Every store quote includes

A fit check — flue size, alloy, venting, and clearances verified against your inspection
Written installed pricing before anything is ordered
Installation to the component's listing by trained technicians
Documentation that closes the finding — so the warranty, your insurer, and the next inspector all see a job done right

Chimney Top — Caps, Covers & Draft

Request a quote

No price is listed — that’s the standard, not a sticker. Installed pricing depends on your flue, alloy, venting, and access, and we confirm it in writing after a fit check. No payment is taken online.

Specify your custom cap

Built to your figures by our fabricator. Spec it here; every measurement is verified on the fit check before a single cut.

Cap style

Size variant

Material

Gauge

Outside measurements

Whole inches plus the fraction, for each side: A (top), B (right), C (bottom), D (left).

A — Topin

B — Rightin

C — Bottomin

D — Leftin

Add 1/2" of clearance to each of the A, B, C and D outside measurements before you submit — Plano fabricates to these exact figures, so the extra half-inch is what lets the finished cap seat over the masonry. I've added the 1/2" clearance to A, B, C and D.

Flue holes

Inside-hole measurements run from the outside edge to the edge of each hole, numbered from the top, then from the left — one pair per flue.

Number of flues

Hole 1

Skirt height

Leg height

Add-ons — available, priced on quote

Rush — faster turnaroundAvailable — priced on quote. (Plano's rush is a 2-business-day fabrication; we confirm the upcharge in writing, never a sticker price online.)Lifetime warrantyAvailable — priced on quote. Plano backs the fabrication for life; we confirm the cost in writing with the rest of the installed quote.

Every figure rides into the quote as your stated spec — confirmed on the measured fit check before fabrication. No price is taken online.

Include professional installationFitted to its listing by the trained crew as Chase Cover Replacement. Leave it on — most parts here are a safety system, not a box you fit on a Saturday.

Pick a preferred window next — we confirm it by phone

(214) 444-8094

Keep browsing

More from the Chimney aisle

Architectural Multi-Flue Shroud (Decorative)

Sheet-metal shroud sized to your chase to dress up a bare capped chimney and finish the roofline properly. You choose the treatment: powder-coat or copper, corbel or hip-roof styling, proportioned so it looks right from the street rather than tacked on. We measure it to your chimney instead of dropping a stock cap on a custom home and calling it finished. Ask the crew to handle the chimney sweep and any masonry the same trip so it is one visit, not three.

View pageQuote

Integrated Crown-Cap Unit (Drip-Edge Crown + Cap)

Full stainless top that caps every flue at once and overhangs the crown to throw water clear of the masonry, so instead of patching concrete that will crack again you seal the whole top in steel that keeps rain off for good. Before we sell it we tell you straight whether the crown needs repair first or whether the cap by itself solves the problem. Since the crew is already on the roof, they can sweep the flue and run the dryer-vent airflow test on the same appointment.

View pageQuote

Powered Draft System (Enervex / Exhausto Inducer + Modulating Control)

Roof-mounted variable-speed fan with a sensor control that mechanically pulls smoke up a stubborn flue and holds a steady draft. This is the last thing we reach for, not the first: nine times out of ten a height correction, a cap swap, or a properly sized liner fixes a draft problem for less money, so we diagnose the fault before we ever quote the fan. When the geometry genuinely cannot draft on its own, this is the engineered answer, commissioned so it actually stops the smoke-back instead of hiding it. We can look at the whole chimney and the vents while we are diagnosing.

View pageQuote

Everything in Chimney Top — Caps, Covers & Draft

10+

Years

NFPA 211

Standard

CSIA

Certified

< 2hr

Response

Ready when you are

Talk to a CSIA-certified expert today.

Free written quote. Same-week scheduling. 24/7 emergency response when you need it.

Book Free Inspection (214) 444-8094

Licensed & Insured Same-Week Scheduling Written Quote, Always

Emergency

24/7 Response

Active leak, animal in flue, post-fire damage, or smoke event? Real humans on the line 7 AM to 12 AM every day — replies in under 2 minutes. Tech dispatch within 2 hours during business hours, subject to crew availability after-hours.

Emergency line